Vertex Standard VX-3R Operating Manual Download

Page: 74 / 85

FCC ID: K6620285X20

IC ID: 511B-20285X20

VX-3R Operating Manual

BEAM: The BUSY/TX indicator glows continuously in white.

BP+BEM: Loud “Alarm” sounds and the BUSY/TX indicator glows continuously in white.

CW: The BUSY/TX indicator flashes according to the programmed Emergency message (Morse

Code)* at a rate of five words per minute.

BP+CW: Sounds tones via the speaker, and flashes the BUSY/TX indicator, according to the

programmed Emergency message (Morse Code)* at a rate of five words per minute.

CWT: Transmits the programmed Emergency message (Morse Code)* and flashes the

BUSY/TX indicator, according to the programmed Emergency message (Morse Code)*

on the air beginning one minute after activation of the Emergency function.

*The internationally-recognized Morse Code “S.O.S” message (•••– – –•••) is programmed at the

factory for the Emergency message.

Here’s how to program the Emergency Message:

1. Set this Set Mode Item to “CW” or “BP+CW.”

2. Press the [V/M] key to display any previously-stored emergency message.

3. Press the [HM/RV] key to clear any previous emergency message, if desired.

4. Rotate the DIAL knob to select the first letter/number of the message, then press the [V/M]

key momentarily to save the first letter/number and move on to the next character.

5. Repeat the previous step as necessary to complete the message (up to 16 characters).

6. If you make a mistake, press the [BAND] key to back-space the cursor; now re-enter the

correct letter/number.

7. Press the [HM/RV] key to delete all data after the cursor that may have been previously

stored erroneously.

8. When you have entered the message, press the [TXPO] key momentarily to confirm the

message, then press the PTT switch to save the settings and exit to normal operation.

Set Mode Item 33 [EXT.MNU]

Function: Enables/Disables the extended Set Mode Menu.

Available Values: ON/OFF

Default: OFF

Set Mode Item 34 [FW KEY]

Function: Set the duration that a secondary function of the [F/W] key (press and holding the [F/W]

key) is held determines the function they activate.

Available Values: FW0.3S/FW0.5S/FW0.7S/ FW1.0S/FW1.5S

Default: FW0.5S

Set Mode Item 35 [HLF.DEV]*

Function: Reducing the Deviation level by 50 %.

Available Values: ON/OFF

Vertex Standard Co., Ltd.

Summary of Contents for VX-3R






















































































Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands

Vertex Standard VX-3R, Operating Manual

Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands