Vertex Standard VX-3R Operating Manual Download

Page: 83 / 85

FCC ID: K6620285X20

IC ID: 511B-20285X20

VX-3R Operating Manual

Function: Setting of the CTCSS Tone Frequency.

Available Values: 50 standard CTCSS tones

Default: 100.0 Hz

Set Mode Item 87 [TOT]

Function: Setting of the TOT time

Available Values: OFF/0.5M - 30M (0.5M/step)

Default: OFF

The time-out timer shuts off the transmitter after continuous transmission of the programmed time.

Set Mode Item 88 [TS MUT]

Function: Enables/Disables the receiver audio output while the Tone Search Scanner is activated.

Available Values: ON/OFF

Default: ON

Set Mode Item 89 [TS SPD]

Function: Selects the Tone Search Scanner speed.

Available Values: SLOW (1.25 tone/sec)/FAST (2.5 tone/sec)

Default: FAST

Set Mode Item 90 [VFO MD]

Function: Selects or disables the VFO band edge limiting for the current band.

Available Values: ALL/BAND

Default: BAND

BAND: When the VFO frequency reaches the high band edge of the current band, the VFO

frequency will jump to the low band edge of the current band (or vice versa).

ALL: When the VFO frequency reaches the high edge of the current band, the VFO frequency will

jump to the low band edge of the next band (or vice versa).

Set Mode Item 91 [VFO.SKP]

Function: Set the My Band.

Available Values: ON/OFF

Default: OFF

The “My Band” feature allows you to select several operating bands, and make only those bands

available for selection via the [BAND] key.

ON: Only the bands that are turned on will be shown when pushing the [BAND] key.

OFF: When the [BAND] key is pressed, the bands that are turned “OFF” will not be shown.

See page ?? for details.

Set Mode Item 92 [WAKEUP]

Function: Setting of the Wakeup feature.

Available Values: OFF/5SEC - 60SEC(5SEC/step)/EAI

Vertex Standard Co., Ltd.

Summary of Contents for VX-3R






















































































Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands

Vertex Standard VX-3R, Operating Manual

Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands