Vertex Standard VX-3R Operating Manual Download

Page: 23 / 85

FCC ID: K6620285X20

IC ID: 511B-20285X20

VX-3R Operating Manual

incoming CTCSS or DCS tone/code.

When the radio detects the correct tone or code, it will halt on that tone/code, and audio will be allowed

to pass. Press the [BAND] key to lock in that tone/code, then press PTT to exit to normal operation.

R.F. Says: If the Tone Scan feature does not detect a tone or code, it will continue to scan indefinitely. When

this happens, it may be that the other station is not sending any tone. You can press the PTT switch to halt

the scan at any time.

You may listen to the (muted) signal from the other station during Tone Scanning when Set Mode Item 88:

TS MUT is set to “OFF.” See page ?? for details. You can also change the Tone Search scanning speed,

using Set Mode Item 89: TS SPD. See page ??.

Tone Scanning works either in the VFO or Memory modes.

EPCS (Enhanced Paging & Code Squelch)

The VX-3R includes an Enhanced CTCSS tone encoder/decoder and a dedicated microprocessor

providing paging and selective calling features. This allows you to place a call to a specific station (Paging),

and to receive calls of your choice directed only to you (Code Squelch).

The paging and code squelch systems use two pairs of (alternately switched) CTCSS tones which are

stored in the pager memories. Basically, your receiver remains silent until it receives the CTCSS tone pair

that matches those stored in the Receiving Pager Memory. The squelch then opens so the caller is heard,

and the paging ringer immediately sounds, if activated. When you close the PTT switch to transmit, the

CTCSS tone pair which is stored in the Transmitting Pager Memory will be transmitted automatically.

On the paged radio, the squelch will close automatically after the incoming page ends. Meanwhile, on the

paging radio, the Enhanced Paging and Code Squelch system will be disabled after the PTT switch is

released after the paging transmission. You may re-activate the Enhanced Paging and Code Squelch

system again.

Storing the CTCSS Tone Pairs for EPCS Operation

1. Press and hold in the [TXPO] key for one second to enter the Set mode.

2. Rotate the DIAL knob to select Set Mode Item 61: PAG.CDR for the Receiving CTCSS Tone Pair or Set

Mode Item 62: PAG.CDT for the Transmitting CTCSS Tone Pair.

Note: Do not forget to pull the DIAL knob to rotate the DIAL knob.

3. Press the [TXPO] key momentarily to enable adjustment of this Set Mode Item.

4. Rotate the DIAL knob to set the CTCSS Tone number which corresponds to the first tone of the CTCSS

Tone Pair.

5. Press the [V/M] key, then rotate the DIAL knob to set the CTCSS Tone number which corresponds to

the second tone of the CTCSS Tone Pair.

Vertex Standard Co., Ltd.

Summary of Contents for VX-3R






















































































Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands

Vertex Standard VX-3R, Operating Manual

Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands