Vertex Standard VX-3R Operating Manual Download

Page: 26 / 85

FCC ID: K6620285X20

IC ID: 511B-20285X20

VX-3R Operating Manual

8. Press the [V/M] key to accept the first beep tone of the User Beep.

9. If you mistake, press the [BAND] key to back-space the cursor, then re-enter the correct beep tone or

length.

10. Repeat steps 6 - 9 until you have completed the User Beep.

11. When there is a beep tone which you wish to delete, bring the cursor to that beep tone using the

[BAND]/[V/M] key, then press the [MODE] key repeatedly till to display the “dEL” notation in the

Memory Channel Number display slot, press and hold in the [MODE] key for one second to delete that

beep tone.

12. When you wish to add the beep tone into the beep tone strings, bring the cursor to the beep tone to the

desired place using the [BAND]/[V/M] key, then press the [MODE] key repeatedly till to display the

“InS” notation in the Memory Channel Number display slot, press and hold in the [MODE] key for one

second to add the beep tone.

13. Press and hold the [HM/RV] key for one second to delete all data after the current position that may

have been previously stored beep.

14. When you have programmed User Beep, press the [TXPO] key momentarily to confirm the User Beep.

R.F. Says: You may check your work by monitoring the programmed User Beep. To do this, repeat steps 1 -

4 above, then press the [F/W] key.

Split Tone Operation

The VX-2R can be operated in a Split Tone configuration via the Set mode.

1. Press and hold in the [H/L] key for one second to enter the Set mode.

2. Rotate the DIAL knob to select Set Mode Item 81: SQSPLT.

Note: Do not forget to pull the DIAL knob to rotate the DIAL knob.

3. Press the [H/L] key momentarily to enable adjustment of this Set Mode Item.

4. Rotate the DIAL knob to select “ON” (to enable the Split Tone feature).

5. Press the PTT switch momentarily to save the new setting and exit to normal operation.

When the Split Tone feature is activated, you can see the following additional parameters after the

“MESSAGE” parameter while selecting the Set Mode Item 79: SQ TYP:

D CODE: DCS Encode only

(the “DCS” icon will blink during operation)

T DCS: Encodes a CTCSS Tone and Decodes a DCS code

(the “T” icon will blink and the “DCS” icon will appear during operation)

D TONE: Encodes a DCS code and Decodes a CTCSS Tone

(the “TSQ” icon will appear and the “DCS” icon will blink during operation)

Select the desired operating mode, from the selections shown above, within Set Mode Item 79.

Vertex Standard Co., Ltd.

Summary of Contents for VX-3R






















































































Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands

Vertex Standard VX-3R, Operating Manual

Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands