Vertex Standard VX-3R Operating Manual Download

Page: 43 / 85

FCC ID: K6620285X20

IC ID: 511B-20285X20

VX-3R Operating Manual

4. Rotate the DIAL knob to set this Set Mode Item to “OFF.”

5. When you have made your selection, press the PTT switch to save the setting and exit to normal

operation.

Band Edge Beeper

The VX-3R will automatically “beep” when a band edge is encountered during scanning (either in standard

VFO scanning or during PMS operation). You may enable this feature (band edge beeper) when the

frequency reaches the band edge while selecting the VFO frequency by the DIAL knob.

The procedure for enabling the Band-Edge Beeper is:

1. Press and hold in the [TXPO] key for one second to enter the Set mode.

2. Rotate the DIAL knob to select Set Mode Item 12: BP EDG.

Note: Do not forget to pull the DIAL knob to rotate the DIAL knob.

3. Press the [TXPO] key momentarily to enable adjustment of this Set Mode Item.

4. Rotate the DIAL knob to set this Set Mode Item to “ON.”

5. When you have made your selection, press the PTT switch to save the setting and exit to normal

operation.

Smart Search Operation

The Smart Search feature allows you to load frequencies automatically according to where activity is

encountered by your radio. When Smart Search is engaged, the transceiver will search above and below

your current frequency, storing active frequencies as it goes (without stopping on them even momentarily);

these frequencies are stored into a special Smart Search memory band, consisting of 31 memories (15

above the current frequency, 15 below the current frequency, plus the current frequency itself).

Two basic operating modes for Smart Search are available:

SINGLE

: In this mode, the transceiver will sweep the current band once in each direction starting on the

current frequency. All channels where activity is present will be loaded into the Smart Search memories;

whether or not all 31 memories are filled, the search will stop after one sweep in each direction.

CONT

: In this mode, the transceiver will make one pass in each direction as with One-Shot searching; if all

31 channels are not filled after the first sweep, however, the radio will continue sweeping until they are all

filled.

Setting the Smart Search Mode

1. Press and hold in the [TXPO] key for one second to enter the Set mode.

2. Rotate the DIAL knob to select Set Mode Item 71: S SRCH.

Note: Do not forget to pull the DIAL knob to rotate the DIAL knob.

Vertex Standard Co., Ltd.

Summary of Contents for VX-3R






















































































Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands

Vertex Standard VX-3R, Operating Manual

Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands