Vertex Standard VX-3R Operating Manual Download

Page: 24 / 85

FCC ID: K6620285X20

IC ID: 511B-20285X20

VX-3R Operating Manual

6. Press the PTT switch to save the new setting and exit to normal operation.

R.F. Says: The VX-3R does not recognize the order of the 1st tone and the 2nd tone. In other words, for

example, the VX-6R considers both CTCSS pairs “10, 35” and “35, 10” to be identical.

Activating the Enhanced Paging & Code Squelch System

1. Press and hold in the [TXPO] key for one second to enter the Set mode.

2. Rotate the DIAL knob to select Set Mode Item 79: SQ TYP.

Note: Do not forget to pull the DIAL knob to rotate the DIAL knob.

3. Press the [TXPO] key momentarily to enable adjustment of this Set Mode Item.

4. Rotate the DIAL knob to select “PAGER”.

5. Press the PTT switch to save the new setting and activate the Enhanced Paging & Code Squelch.

To disable the Enhanced Paging & Code Squelch, just repeat the above procedure, rotate the DIAL knob to

select “OFF” in step 4 above.

When the Enhanced Paging & Code Squelch feature is activated, the “P” notation will appear at the 100

MHz digit of the frequency display.

R.F. Says: During Enhanced Paging & Code Squelch operation, you may set up the VX-3R such that a

ringing “bell” sound alerts you to the fact that a call is coming in. See page ?? for details.

Paging Answer Back

When you press the PTT switch to respond to a page call, the VX-3R transmits the same CTCSS tone pair.

This tone pair will open the Code Squelch of the calling station. If you prefer, you can have the VX-3R

respond to page calls automatically (“transpond”).To enable this feature:

1. Press and hold in the [TXPO] key for one second to enter the Set mode.

2. Rotate the DIAL knob to select Set Mode Item 60: PAG.ABK.

Note: Do not forget to pull the DIAL knob to rotate the DIAL knob.

3. Press the [TXPO] key momentarily to enable adjustment of this Set Mode Item.

4. Rotate the DIAL knob to select “ON”.

5. Press the PTT switch to save the new setting and exit to normal operation.

R.F. Says: The Paging Answer Back feature constitutes a form of “remote control” operation that may be

restricted to certain frequencies. U.S. users should confirm the current status of $97.201(b) of the FCC’s

rules governing the Amateur service before utilizing this feature on the 144 MHz band.

CTCSS/DCS/EPCS Bell Operation

During CTCSS Decode, DCS, or EPCS operation, you may set up the VX-3R such that a ringing “bell”

sound (or user programmed beep) alerts you to the fact that a call is coming in. Here is the procedure for

activating the CTCSS/DCS/EPCS Bell:

Vertex Standard Co., Ltd.

Summary of Contents for VX-3R






















































































Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands

Vertex Standard VX-3R, Operating Manual

Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands