Vertex Standard VX-3R Operating Manual Download

Page: 1 / 85

FCC ID: K6620285X20

IC ID: 511B-20285X20

VX-3R Operating Manual

General Description

The VX-3R is a micro-miniature multiband FM transceiver with extensive receive frequency coverage,

providing local-area two-way amateur communications along with unmatched monitoring capability.

The VX-3R’s incredibly small size allows you to take it anywhere - hiking, skiing, or while walking around

town - and its operating flexibility brings the user many avenues of operating enjoyment. Its incredibly tiny

FNB-82LI Lithium-Ion Battery Pack provides up to 1.5 Watts of transmit power on VHF, and 1 Watt on UHF.

Besides 144- and 430-MHz transceive operation, the VX-3R provides receive coverage of the AM (MF)

which provide the internal bar antenna and FM broadcast bands, HF Shortwave Bands, VHF and UHF TV

bands, the VHF AM aircraft band, and a wide range of commercial and public safety frequencies!

Furthermore, the VX-3R provides the internal bar antenna for the good receiving the AM broadcast.

Additional features include an Enhanced Paging and Code Squelch (EPCS), which allows you to page a

particular station and only receive calls from that station, if desired; a security Password feature, which will

allow you to turn on and operate your transceiver only after you enter your Password; a convenient access

key for Vertex Standard’s WIRES

™

(Wide-Coverage Internet Repeater Enhancement System); Emergency

Automatic ID (EAI) function, that will automatically cause your VX-3R to transmit your callsign and engage

your rig’s microphone, even if you are disabled and unable to press the PTT switch; a transmit Time-Out

Timer (TOT); Automatic Power-Off (APO); Automatic Repeater Shift (ARS); Yaesu’s exclusive ARTS

™

(Auto-Range Transponder System) which “beeps” the user when you move out of communications range

with another ARTS

equipped station, plus provision for reduction of the TX deviation in areas of high

channel congestion. And an S-meter squelch circuit allows the owner to set the squelch to open at a

programmable setting of the S-Meter, thus reducing guesswork in setting the squelch threshold.

We appreciate your purchase of the VX-3R, and encourage you to read this manual thoroughly, so as to

learn about the many exciting features of your exciting new Yaesu hand-held transceiver!

Accessories & Options

Supplied Accessories

FNB-82LI

3.7 V, 1000 mAh Rechargeable Lithium Ion Battery Pack

NC-85A/B, C, U*

2.5-Hour Charger

YHA-66

Antenna

Operating Manual

Warranty Card

Available Options

FNB-82LI

3.7 V, 1000 mAh Rechargeable Lithium Ion Battery Pack

FBA-37

Dry Cell Battery Case for 3 x “AA” Alkaline Cells

Vertex Standard Co., Ltd.

Summary of Contents for VX-3R






















































































Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands

Vertex Standard VX-3R, Operating Manual

Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands