Vertex Standard VX-3R Operating Manual Download

Page: 46 / 85

FCC ID: K6620285X20

IC ID: 511B-20285X20

VX-3R Operating Manual

factory-programmed message of course can be overwritten at any time with personalized messages.

1. Press and hold in the [TXPO] key for one second to enter the Set mode.

2. Rotate the DIAL knob to select Set Mode Item 57: MSG.SEL.

Note: Do not forget to pull the DIAL knob to rotate the DIAL knob.

3. Press the [TXPO] key momentarily to enable adjustment of this Set Mode Item.

4. Rotate the DIAL knob to select the desired Message slot into which you wish to store a message. The

LCD displays the previously stored message.

5. Press the [TXPO] key momentarily to enable programming of the message.

6. Press the [HM/RV] key to clear the previously stored message, if desired.

7. Rotate the DIAL knob to select the first character of the message you wish to store, and then press the

[V/M] key to save the first character of the message and move on to the next place.

8. Repeat the previous step to complete the message (up to 16 characters). If you make a mistake, press

the [BAND] key to move back to the incorrect character, then re-enter the correct character.

9. Press the [HM/RV] key to delete all data after the cursor that may have been previously stored

erroneously.

10. When the Message entry is complete, press the [TXPO] key momentarily.

11. If you wish to store another message, repeat steps 3 through 10 above.

12. Press the PTT switch to exit to normal operation.

Programming a Member List

(Requires all members set the same member list (includes own ID) into the same member box in the same

order.)

It is possible to register a maximum of 20 persons, in order to identify the sender. When you receive a

message transfer, you can know who sent the message by the ID in the register. In addition, your ID can be

sent to the members when you transmit any messages to them.

If all the members share the register information (ID), the message sender ID will be shown on the display

when receiving the message.

Even if no IDs are registered, the function can work. However, in this case, “message sender ID” will be not

displayed when receiving a message.

We recommend that you use your call sign for the member list.

1. Press and hold in the [TXPO] key for one second to enter the Set mode.

2. Rotate the DIAL knob to select Set Mode Item 50: MSG.LST.

Note: Do not forget to pull the DIAL knob to rotate the DIAL knob.

3. Press the [TXPO] key momentarily to enable adjustment of this Set Mode Item.

4. Rotate the DIAL knob to select the desired member box (01 ~ 20) into which you wish to store a

member ID. The LCD will display the previously stored personal ID.

Vertex Standard Co., Ltd.

Summary of Contents for VX-3R






















































































Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands

Vertex Standard VX-3R, Operating Manual

Search results

Summary of Contents for VX-3R

Reviews:

Related manuals for VX-3R

Brands by name

Popular brands