DE
GB
RUS
43
Offset-Abschaltung
Der Regler ist mit einer bedarfs-
abhängigen Heizungsabschaltung
ausgestattet. Diese Funktion kann dann
zu Problemen führen, wenn die Außen-
temperatur schnell ansteigt, die nach
Norden gelegenen Räume aber noch
kühl sind. Durch die Abschaltung würden
diese Räume nicht mehr erwärmt.
Um dieses Problem zu vermeiden kann für
jeden Kreis ein Offset von 0°C bis 20°C
eingegeben werden. In der Regel empfiehlt
sich zusätzlich eine Fußpunktanhebung.
Temperaturprofil
Mit dieser Funktion wird ein Temperatur-
profil durchlaufen, wie es z. B. zur
Trocknung eines Estrichs eingesetzt wird.
Die Vorlauftemperatur des Heizkreises wird
automatisch auf die in Tabelle 6.2 angege-
benen Temperaturen geregelt. Alle anderen
Betriebsarten werden für die Dauer der
Funktion unterdrückt. Beim Start der
Funktion wird die aktuelle Uhrzeit als
Startzeit gespeichert. Der Tageswechsel
während des Programmablaufs erfolgt
jeweils zu dieser Uhrzeit. Während die
Funktion aktiv ist, werden im Display des
Reglers der Betriebsmodus, der Tag und die
Vorlaufsolltemperatur angezeigt.
Wenn die Funktion wegen Netzausfall ab-
gebrochen wurde, startet der Regler an-
schließend automatisch die Funktion mit
dem 1. Tag (Zyklus 1). Wurde der 1. Zyklus
vor dem Netzausfall bereits vollständig
Offset-cutoff (Temp. offset)
The controller is fitted with a need-
dependent heating-system shutoff device.
This function can give rise to problems if
the external temperature rises fast but
north-facing rooms nevertheless remain
cold. System shutdown then leaves these
rooms without heating.
In order to avoid this problem, an offset
of 0 °C to 20 °C can be entered for each
circuit. It is normally advisable to to
program in a low-point increase at the
same time.
Temperature profile
With this function a temperature profile is
passed through such as is used, for
example, for drying flooring plaster. The
flow temperature of the heating circuit is
adjusted automatically to the temperatures
shown in Table 6.2. All other operating
modes are suppressed for the duration of
the function.
At the start of the function the current time
of the day is stored as the starting time.
The change of day during the course of the
program always takes place at this time.
While the function is active, the operating
mode, the day and the required flow
temperature are shown in the controllers
display.
If the function has been interrupted due to a
power failure, the controller then automati-
cally starts the function with day 1 (cycle 1).
If the 1st cycle has already been fully
О
Оф
фссе
етт о
оттккллю
ючче
енни
ие
е
Регулятор оснащён системой отключения
отопления, управляемой по температуре
наружного воздуха. Это может привести к
определённым проблемам, если
температура наружного воздуха быстро
увеличивается, а расположенные на
северной стороне помещения ещё остаются
холодными. Изза такого отключения эти
помещения вообще перестали бы
отапливаться. Для предотвращения таких
проблем для каждого контура может быть
введено дополнительное смещение
комнатной температуры от 0
°
С до 20
°
С. Как
правило, дополнительно ещё рекомендуется
регулировка опорной точки включения
отопительного контура.
О
Одднно
оввр
ре
ем
ме
енннны
ый
й сс о
отто
опплле
енни
ие
ем
м нна
аггр
ре
евв
б
бо
ой
йлле
ер
ра
а
Чтобы обеспечить приготовление горячей
воды параллельно работе отопления, ото
пительный котёл должен развивать соответ
ствующую мощность. Эта функция может
быть реализована только в системах с насо
сом обогрева бойлера. Для котлов с прио
ритетным переключающим вентилем данная
установка должна быть выключена (=0).
Только смесительный контур может
функционировать параллельно нагреву
бойлера, работа прямого контура
блокируется.
Summary of Contents for VRC 410
