manualshive.com logo in svg

Toshiba SATELLITE M40 Series, Maintenance Manual

Share
Download
Toshiba SATELLITE M40 Series Maintenance Manual Download Page 96

3  Diagnostic Programs

 

3.3 Option

 

22

      

Satellite M40/M45 TECRA A4 Dynabook Vx/4  Maintenance Manual 

3.3.6   LOG Parameters Setting 

You can access the Log Parameters screen through Service Diagnostics\Options - 
Generate Report. 

 

?

 

Report Destination

 

If  selecting 'NONE', no log file will be generated; if selecting 'FILE', a log file with 
the name specified in 'Log File Name' will be generated.  

?

 

Log Options

 

?

 

Log Errors

 

If selecting this parameter, errors will be recorded when the test fails. 

?

 

Log Test Activities 

If selecting this parameter, the subtest results will be recorded. 

?

 

Log Test Start Time  

If selecting this parameter, the start time of the test will be recorded.  

?

 

Log Test End Time  

If selecting this parameter, the end time of the test will be recorded.  

?

 

Log Errors Only 

If selecting this parameter, errors will be recorded only when the test fails.  

?

 

Log Errors Only with Time  

Summary of Contents for SATELLITE M40 Series




























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands