Toshiba SATELLITE M40 Series Maintenance Manual Download Page 82 | Manualshive

Page: 82 / 283

Toshiba SATELLITE M40 Series Maintenance Manual Download Page 82

3 Diagnostic Programs

3.2 Quick Start

8

Satellite M40/M45 TECRA A4 Dynabook Vx/4 Maintenance Manual

When the user has checked all the keys and all the keys in the screen have changed
color, the diagnostics program would automatically end the test and report the pass
information.

If keyboard test fails, program will terminate the test and report the fail information
when it is time to timeout.

The test will end when all keys are pressed or test time is out after 100 seconds.

3.2.4 Hotkey Test

Check whether Hotkey run well.

3.2.5 Audio Play Test

Check whether the system could playback audio normally. When the test is completed, a
file named Audio_P.log will be saved in the defined location.

3.2.6 Audio Record Test

Check whether the system could record the sound and playback it normally. Before the
test, please make sure that the linked line is inserted and the volume is set to maximum.
When the test is completed, a file named Audio_R.log will be saved in the defined
location.

3.2.7 DMI Read

Read the information from the system’s SMBIOS and display it in the screen as follows:

«
...
80
81
82
83
84
...
»

Summary of Contents for SATELLITE M40 Series




























































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands