manualshive.com logo in svg

Toshiba SATELLITE M40 Series, Maintenance Manual

Share
Download
Toshiba SATELLITE M40 Series Maintenance Manual Download Page 190

4.9 Display Assembly

 

4 Replacement Procedures

 

Satellite M40/M45, TECRA A4, dynabook V x/4 Maintenance Manual

 

4-41

 

 

Figure 4-28 Removing the display assembly 

 

Installing the Display Assembly 

Install the display assembly according to the following procedures and Figures 4-19, 4-20. 

1.

 

Place the display panel in the correct position and push the wireless antenna cable into the 
top cover. 

2.

 

Connect the LCD/FL cable to CN1 on the system board  

3.

 

Securing display assembly with two M2.5x5 black flat-head screws. 

4.

 

Close the display panel and turn the computer back to front and fix it with four M2.5x8 
black flat-head screws. 

Summary of Contents for SATELLITE M40 Series




























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands