manualshive.com logo in svg

Toshiba SATELLITE M40 Series, Maintenance Manual

Share
Download
Toshiba SATELLITE M40 Series Maintenance Manual Download Page 59

2  Troubleshooting 

2.5  2.5-inch HDD 

2-14 

Satellite M40/M45 TECRA A4 dynabook Vx/4  Maintenance Manual

 

Procedure 5 Connector Check and Replacement Check 

The HDD or system board may be faulty.  Disassemble the computer following the steps 
described in Chapter 4 and perform the following checks: 
 

Check 1 

  Make sure the following connectors have been firmly connected to the 
HDD, system board and CPU. 

HDD

System board

CPU

 

 

If any connector is loose or off, reconnect it firmly and return to Procedure 1.  
If there is still an error, perform Check 2. 
 
Check 2 

The HDD may be damaged. Replace it with a new one following the 
disassembling instructions in Chapter 4.  If the problem persists, perform 
Check 3. 

 
Check 3 

The System board may be damaged.  Replace it with a new one following 
the disassembling instructions in Chapter 4.  If the problem persists, 
perform Check 4. 

 
Check 4 

The CPU may be damaged.  Replace it with a new one following the 
disassembling instructions in Chapter 4.

Summary of Contents for SATELLITE M40 Series




























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands