Toshiba SATELLITE M40 Series Maintenance Manual Download Page 140

Page: 140 / 283

3 Diagnostic Programs

3.11Error Codes and Description

Satellite M40/M45 TECRA A4 Dynabook Vx/4 Maintenance Manual

controller

20xx

IDE-HDD

Get Parameter Fail !

Wrong test parameters are input
by user.

Reinput the correct parameters.

Write Pattern Error

HD is damaged.

Send the HD for repair.

Data Compare Error

HD is damaged.

As above.

Read Verify Error

HD is damaged.

As above.

Seek Error

HD is damaged.

As above.

Disk Controller Self Test
Failed

The HD controller is damaged.

As above.

Disk Controller Test
unexpected interrupt
Failed

The HD controller is damaged.

As above.

Disk Controller action
Test Failed

The HD controller is damaged.

As above.

Disk dos not support
SMART

Disk dos not support SMART

Change HD which supported
SMART and test again

Disk read attribute
threshold error

Disk read attribute threshold
error

Send the HD for repair.

Disk read attribute value
error

Disk read attribute value error

As above.

Disk SMART attribute
value error

Disk SMART attribute value
error

As above.

21xx

ODD

No Disk in CDROM

No disk is found in the CD-
ROM.

Insert a disk into the CD-ROM.

The Disk in CDROM is
not Data Disk

The disk in the CD-ROM is not
Data Disk.

Insert a DATA CD.

IDE-CD Controller Error Functional errors with the CD-

ROM.

Send the CD-ROM for repair.

CD Read Error

Either the disk or the CD-ROM
is damaged.

Replace the disk or send the CD-
ROM for repair.

CD Seek Error

Either the disk or the CD-ROM
is damaged.

Replace the disk or send the CD-
ROM for repair.

Eject Error

Wrong CD-ROM drive.

Exit from the wrong drive.

Summary of Contents for SATELLITE M40 Series




























































































































































































































































































Search results

Summary of Contents for SATELLITE M40 Series

Reviews:

Brands by name

Popular brands

Toshiba SATELLITE M40 Series, Maintenance Manual

Search results

Summary of Contents for SATELLITE M40 Series

Reviews:

Brands by name

Popular brands