Toshiba SATELLITE M40 Series Maintenance Manual Download Page 211

Page: 211 / 283

4 Replacement Procedures

4.19 Touch Pad and Button Board

4-62

Satellite M40/M45, TECRA A4, dynabook Vx/4 Maintenance Manual

4.19

Touch Pad and Button Board

Removing the Touch Pad and Button Board

Remove the touch pad and button board according to the following procedures and Figure 4-44.

Disconnect the touch pad flat cables from J1 on the touch pad.

Remove the two M2.5x4 black flat-head screws for securing the touch pad.

Remove the Touch Pad.

Figure 4-44 Removing the touch pad and button board

Remove the two M2.5x3 flat-round-head screws for securing the touch pad board.

Remove the Touch Pad board.

Disconnect the touch pad flat cable from CN3000 and button board flat cable from
CN3001 on the button board.

Summary of Contents for SATELLITE M40 Series




























































































































































































































































































Search results

Summary of Contents for SATELLITE M40 Series

Reviews:

Brands by name

Popular brands

Toshiba SATELLITE M40 Series, Maintenance Manual

Search results

Summary of Contents for SATELLITE M40 Series

Reviews:

Brands by name

Popular brands