manualshive.com logo in svg

Toshiba SATELLITE M40 Series, Maintenance Manual

Share
Download
Toshiba SATELLITE M40 Series Maintenance Manual Download Page 132

3  Diagnostic Programs

 

 

3.10 Peripheral

 

58

      

Satellite M40/M45 TECRA A4 Dynabook Vx/4  Maintenance Manual 

3.10  Peripheral 

Subtest 01 

 Keyboard 

This test item is to check whether the keyboard works normally. 

1.

 

Keyboard Data Line Test 

Check whether the keyboard data line works normally. 

2.

 

Keyboard Led Test 

Check whether the keyboard led works normally. 

 

3.

 

Keyboard Clock Line Test 

Check whether the keyboard clock line works normally.

 

Subtest 02 

 Mouse Test 

Check whether the point devices work normally. 

1.

 

Touch Pad 

Before test Touch Pad’s function, user should set a timeout time at below screen: 

 

 

Summary of Contents for SATELLITE M40 Series




























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands