manualshive.com logo in svg

Toshiba SATELLITE M40 Series, Maintenance Manual

Share
Download
Toshiba SATELLITE M40 Series Maintenance Manual Download Page 179

4 Replacement Procedures

 

4.5 CPU

 

4-30

 

Satellite M40/M45, TECRA A4, dynabook V x/4 Maintenance Manual

 

4 

1 

4.5  CPU 

Removing the CPU 

Remove the CPU according to the following procedures and Figures 4-18, 4-19 and 4-10. 

CAUTION:  

Remove the CPU by aligning the triangle with the shaded area.

 

 

NOTE: 

FOXCONN CPU socket will be 180 degrees 

to the right.

 

1.

 

Unlock the CPU by rotating the cam on the CPU socket 120 degrees to the left with a flat-
blade screwdriver (in the order shown in the figure below). 

2.

 

Remove the CPU. 

 

Figure4-18 Removing the CPU 

CAUTION:  

When removing the CPU, keep the following in mind:

 

The CPU can become very hot during operation. Be sure to let it cool down before 
starting repair work.

 

Summary of Contents for SATELLITE M40 Series




























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands