manualshive.com logo in svg

Toshiba SATELLITE M40 Series, Maintenance Manual

Share
Download
Toshiba SATELLITE M40 Series Maintenance Manual Download Page 210

4.18 Switch Cover and Switch board

 

4 Replacement Procedures

 

Satellite M40/M45, TECRA A4, dynabook Vx/4 Maintenance Manual

 

4

-

61

 

 

Figure 4-43 Removing the switch Board 

 

Install the Switch Cover and Switch Board 

Install the switch board according to the following procedures and Figure 4-42, 4-43.  

1.

 

Place the switch board on the correct position and securing it with the two M2.5x4 black 
flat-head screws.  

2.

 

Connect the switch board flat cables to CN3002 on the switch board. 

3.

 

Place the switch cover in the correct position and fasten the following 6 latches, in that order:  
-Three latches on each of the left and right sides 

Summary of Contents for SATELLITE M40 Series




























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands