manualshive.com logo in svg

Toshiba SATELLITE M40 Series, Maintenance Manual

Share
Download
Toshiba SATELLITE M40 Series Maintenance Manual Download Page 182

4.6 Speaker cover and Keyboard

 

4 Replacement Procedures

 

Satellite M40/M45, TECRA A4, dynabook V x/4 Maintenance Manual

 

4-33

 

4.6  Speaker Cover and Keyboard 

Removing the Speaker Cover and Keyboard 

Remove the Speaker Cover and Keyboard according to the following procedures and Figure 4-21, 
4-22.  

1.

 

Release the following 8 latches on the switch cover, in that order: 
- Two bottom latches 
- One latch on the left and right sides 
- Four front latches 

2.

 

Remove the speaker cover. 

3.

 

Remove two M2.5x2.6 black bind securing screw. 

4.

 

Remove the connector CN8 on main board and keyboard.    

 

Figure 4-21 Removing the speaker cover 

Summary of Contents for SATELLITE M40 Series




























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands