manualshive.com logo in svg

Toshiba SATELLITE M40 Series, Maintenance Manual

Share
Download
Toshiba SATELLITE M40 Series Maintenance Manual Download Page 194

4.11 System Board, Speaker and MIC, AC-IN,

                

4 Replacement Procedures RJ11/45, MDC cable

Satellite M40/M45, TECRA A4, dynabook Vx/4 Maintenance Manual

 

4

-

45

 

4.11

 

 System Board, Speaker and MIC, AC-IN, RJ11/45, MDC cable 

Removing the System Board, Speaker and MIC, AC-IN, RJ11/45, MDC cable 

NOTE: 

Be careful of the eject button for the PC card. It can be damage when removing 

the board. Make sure it is pushed in. 

Remove the System Board, Speaker and MIC, AC-IN, RJ11/45, MDC cable according to the 
following procedures and Figures 4-31, 4-32 and 4-33.  

1.

 

Remove the MIC cables fix tape. 

2.

 

Remove the MIC cable from CN11. 

3.

 

Remove the L. speaker, R. speaker cable from CN2, CN4 on system board. 

4.

 

Remove the cable cover. 

5.

 

Remove two M2x4 black flat-head screws, and then remove the system board with 
RJ11/45, AC-IN connector. 

 

Figure 4-31 Removing the system board 

5.

 

Turn the system board upside down. 

Summary of Contents for SATELLITE M40 Series




























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands