Toshiba SATELLITE M40 Series Maintenance Manual Download Page 4 | Manualshive

Page: 4 / 283

Toshiba SATELLITE M40 Series Maintenance Manual Download Page 4

Toshiba

Satellite M40 Maintenance Manual

Preface

This maintenance manual describes how to perform hardware service maintenance for the Toshiba
Personal Computer Satellite M40, referred to as Satellite M40 in this manual.

The procedures described in this manual are intended to help service technicians isolate faulty Field
Replaceable Units (FRUs) and replace them in the field.

SAFETY PRECAUTIONS

Four types of messages are used in this manual to bring important information to your attention.
Each of these messages will be italicized and identified as shown below.

DANGER:

“Danger” indicates the existence of a hazard that could result in death or

serious bodily injury, if the safety instruction is not observed.

WARNING:

“Warning” indicates the existence of a hazard that could result in bodily

injury, if the safety instruction is not observed.

CAUTION:

“Caution” indicates the existence of a hazard that could result in property

damage, if the safety instruction is not observed.

NOTE:

“Note” contains general information that relates to your safe maintenance

service.

Improper repair of the computer may result in safety hazards. Toshiba requires service technicians
and authorized dealers or service providers to ensure the following safety precautions are adhered
to strictly.

?

Be sure to fasten screws securely with the right screwdriver. If a screw is not fully fastened,
it could come loose, creating a danger of a short circuit, which could cause overheating,
smoke or fire.

?

If you replace the battery pack, RTC battery or backup battery, be sure to use only the
same model battery or an equivalent battery recommended by Toshiba. Installation of the
wrong battery can cause the battery to explode.

«
...
2
3
4
5
6
...
»

Summary of Contents for SATELLITE M40 Series




























































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands