Toshiba SATELLITE M40 Series Maintenance Manual Download Page 52

Page: 52 / 283

2.3 Power Supply

2 Troubleshooting

Satellite M40/M45 TECRA A4 dynabook Vx/4 Maintenance Manual

2-7

DC IN LED

DC IN LED

Power supply status

On in Green

DC power being supplied (from the AC adapter)

Off

Battery damage and can’t charge during DC-in.

Off

Else

If the DC IN LED off, follow the steps below:

Remove the battery pack and the AC adapter to shut off power supply to the
computer.

Attach the battery and AC adapter back again.

If the LED still off, follow the steps below:

Check 1

Make sure the DC IN LED goes on in Green. If it does not, go to Procedure 2.

Check 2

Make sure the Battery LED goes on in Amber or Green. If it does not, go to
Procedure 3.

Summary of Contents for SATELLITE M40 Series




























































































































































































































































































Search results

Summary of Contents for SATELLITE M40 Series

Reviews:

Brands by name

Popular brands

Toshiba SATELLITE M40 Series, Maintenance Manual

Search results

Summary of Contents for SATELLITE M40 Series

Reviews:

Brands by name

Popular brands