Toshiba SATELLITE M40 Series Maintenance Manual Download Page 122

Page: 122 / 283

3 Diagnostic Programs

3.8 Video

Satellite M40/M45 TECRA A4 Dynabook Vx/4 Maintenance Manual

In the test, user is required to respond according to the instruction in the screen.

Subtest 02

640 * 480 VGA Mode

This test item is to check whether 680*480 VGA Text mode works normally.

In the test, user is required to respond according to the instruction in the screen.

Subtest 03

VESA Video Modes

This test item is to check whether all the video modes supported by the video card
works normally.

In the test, user is required to respond following the instruction in the screen.

Summary of Contents for SATELLITE M40 Series




























































































































































































































































































Search results

Summary of Contents for SATELLITE M40 Series

Reviews:

Brands by name

Popular brands

Toshiba SATELLITE M40 Series, Maintenance Manual

Search results

Summary of Contents for SATELLITE M40 Series

Reviews:

Brands by name

Popular brands