manualshive.com logo in svg

Toshiba SATELLITE M40 Series, Maintenance Manual

Share
Download
Toshiba SATELLITE M40 Series Maintenance Manual Download Page 176

4 Replacement Procedures

 

4.4 CPU Cooling Module

 

4-28

 

Satellite M40/M45, TECRA A4, dynabook V x/4 Maintenance Manual

 

4.4  Cooling Module 

CAUTION: 

When removing the cooling module, keep the following in mind:

 

The cooling module can become very hot during operation. Be sure to let it cool down 
before starting the repair work. 

 

Do not touch or give shock to the fan in the cooling module.

 

 

NOTE: 

The screws for Steps 2 and 3 cannot be removed, only loosened. 

Removing the Cooling Module 

Remove the cooling module according to the following procedures and Figures 4-15, 4-16.  

1.

 

Turn the computer upside down.  

2.

 

Release the CPU cover securing screw. 

3.

 

Remove the CPU cover. 

4.

 

Release the three screws on the cooling module using the numbered order shown to the 
screw. 

5.

 

Remove the cooling module. 

 

Figure 4-15 Removing the CPU cover 

Summary of Contents for SATELLITE M40 Series




























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands