manualshive.com logo in svg

Toshiba SATELLITE M40 Series, Maintenance Manual

Share
Download
Toshiba SATELLITE M40 Series Maintenance Manual Download Page 282

Apx. G  EC/KBC Rewrite Procedures 

Appendices 

Satellite M40/M45 TECRA A4 dynabook VX/4  Maintenance Manual

 

G-1

 

Appendix H  

 

Appendix G  EC/KBC Rewrite Procedures 

This Appendix explains how to rewrite the EC/KBC system program when you update the 
EC/KBC system. 

Tools 

To rewrite the EC/KBC, you need the following tool: 

?

 

BIOS/EC/KBC rewriting disk for the computer 

 

Rewriting the EC/KBC 

1.

 

Set the system to boot mode. 

2.

 

Turn off the power to the computer. 

3.

 

Remove the external cable and PC Card. 

4.

 

Connect an external FDD and insert the BIOS/EC/KBC rewriting disk into either the 
external FDD. 

5.

 

Turn on the power while holding down the [

`

~

]

 

key.  (Keep holding down the key until a 

message appears on the screen.)  The EC/KBC rewriting starts. 

6.

 

When the EC/KBC rewrite is completed, the system is automatically turned off. 

Summary of Contents for SATELLITE M40 Series




























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands