manualshive.com logo in svg

Toshiba SATELLITE M40 Series, Maintenance Manual

Share
Download
Toshiba SATELLITE M40 Series Maintenance Manual Download Page 53

2  Troubleshooting 

2.3  Power Supply 

2-8 

Satellite M40/M45 TECRA A4 dynabook Vx/4  Maintenance Manual

 

Procedure 2  Connection Check 

Power is supplied to the system board as illustrated below:  

    AC
adaptor

System board

AC power cord

AC adaptor cord

Battery pack

 

 
Follow the steps below to check whether each connector has been connected correctly:  

Check 1 

Make sure the AC adaptor and AC po wer cord have been firmly plugged 
into the DC IN 15V socket and wall outlet, respectively.  When they have 
been connected correctly, perform Check 2. 

Check 2 

Connect a new AC adaptor and AC power cord. 

?

 

If the DC IN LED does not go on, go to Procedure 3. 

?

 

If the battery LED does not go on, perform Check 3. 

Check 3 

Make sure the battery pack has been correctly installed in the computer. 
If the battery LED does not go on while the battery pack has been installed 
correctly, go to Procedure 3. 

Procedure 3  Replacement Check 

The system board, power supply board, or CPU may be faulty.  Disassemble the computer 
according to Chapter 4 and follow the steps below:  

 
Check 1 

Replace the power supply board with a new one.  If the battery pack is still 
not working properly, perform Check 2. 

 
Check 2 

Replace the system board with a new one.  If the battery pack is still not 
working properly, perform Check 3. 

 
Check 3 

Replace the CPU with a new one.

Summary of Contents for SATELLITE M40 Series




























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands