manualshive.com logo in svg

Toshiba e-Studio477s, Service Manual, Page: 67 / 482

Share
Download
Toshiba e-Studio477s Service Manual Download Page 67

3

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO477S/527S/477SL

SELF-DIAGNOSTIC MODE

3 - 43

The general relations between the above 4 factors and toner consumption per output page in the copy 
function are as follows:

Fig. 3-1 Factors affecting toner consumption and the tendency

[ 3 ] Details of pixel counter

• Toner cartridge reference and service technician reference

The pixel counter function in this equipment has 2 references, toner cartridge reference and service 
technician reference.

Toner cartridge reference

This is a system that accumulates data between the installation of a new toner cartridge and next 
installation.
The installation of new toner cartridge is judged when the total number of pixel count or output 
pages after the detection of toner cartridge empty has exceeded the threshold.
When the new toner cartridge is judged as installed, the data related with the previous cartridge is 
cleared and replaced with the data after the installation of new cartridge. Clearing of the counter of 
the toner cartridge reference is performed in the setting mode (08-6503).

Service technician reference

This is a system that accumulates data between clearing the counter of the service technician 
reference by service technician and subsequently clearing the same counter.
Clearing of the counter of the service technician reference is performed in the setting mode (08-
6502).

Toner consumption

Toner consumption

Toner consumption

Toner consumption

Original coverage

Original density

Original mode

Density setting

TEXT

/PHOTO

TEXT

PHOTO

PRINTED

IMAGE

MAP

Manual

density

-5

Manual

density

-1

Automatic

density

Manual

density

Center

Manual

density

+1

Manual

density

+5

Summary of Contents for e-Studio477s



































































































































































































































































































































































































































































































Reviews:

No comments