manualshive.com logo in svg

Toshiba e-Studio477s, Service Manual, Page: 241 / 482

Share
Download
Toshiba e-Studio477s Service Manual Download Page 241

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO477S/527S/477SL

REPLACEMENT OF PC BOARDS/HDD

6 - 27

6

(4) Press the [INSTALL] button.

(5) Install the one-time dongle in the equipment (the one which you used for returning the selected 

license before replacing the equipment). Then press the [OK] button.

(6) Select the license to be installed, and then press the [INSTALL] button.

(7) The screen for notifying that the installation will be started is displayed. Then press the [YES] 

button.

(8) After 10 to 40 seconds have passed, the screen for notifying the success of the performance is 

displayed. Then press the [OK] button. If the screen for notifying a failure of the performance is 
displayed, quit this operation by pressing the [NO] button. Then check that the one-time dongle is 
installed properly in the equipment.

(9) Check that the installed license is displayed on the license list.

Remarks: 

• If there are any other licenses to be installed, repeat from step (4).
• If there are no other licenses to be installed, press the [CLOSE] button, and then turn the 

power OFF.

[L] Enable HDD encryption

If the HDD encryption function is used, follow the procedure below.

(1) Start up with the Setting mode (08).

(2) Enter the password, and then press the [OK] button.

(If the password is not set for Service, press the [ENTER] button without entering anything.)

(3) Enable the encryption function.

•  For high security mode

Set the value of 08-8911 to "3".

• For enabling HDD encryption only

Set the value of 08-8911 to "1", and then set the value of 08-9379 to "1" (Security priority) or 
"2" (Performance priority).

(4) Turn the power OFF.

[M] Adjust image quality

(1) Start up with the Adjustment mode (05).

(2) Enter the password, and then press the [OK] button.

(If the password is not set for Service, press the [ENTER] button without entering anything.)

(3) Perform “Automatic gamma adjustment” (05-7165).

 P. 4-4 "4.2.1 Automatic gamma adjustment"

(4) Turn the power OFF.

[N] Initialize settings when FAX Unit (GD-1340) is installed

(1) Reinstall the FAX Unit (GD-1340).

(2) Start up with the Setting mode (08).

Summary of Contents for e-Studio477s



































































































































































































































































































































































































































































































Reviews:

No comments