manualshive.com logo in svg

Toshiba e-Studio477s, Service Manual, Page: 26 / 482

Share
Download
Toshiba e-Studio477s Service Manual Download Page 26

e-STUDIO477S/527S/477SL

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

SELF-DIAGNOSTIC MODE

3 - 2

Notes: 

The following modes cannot be carried out since they are provided only for production.

[2]+[CLEAR]+[POWER]
[7]+[CLEAR]+[POWER]
[8]+[CLEAR]+[POWER]

The menu below can be carried out in the following mode; however, there is no effect on the 
equipment even if it is done.

[9]+[CLEAR]+[POWER]
0. Turn Line Mode ON
1. Turn Line Mode OFF
3. Restore Machine Information

[D] State transition diagram of self-diagnosis modes

Fig. 3-1

*1 If you have used a self-diagnostic mode, turn the power OFF before the customer starts using the 
equipment
*2 Mode shown in the table "[C] List of modes"

[E] About each mode

• Control panel check mode (01)

Operation procedure

Notes: 

• A mode can be cancelled by [POWER] OFF/ON when the LED is lit and the LCD is blinking.
• Button Check

Buttons with LED: Press to turn OFF the LED.
Buttons without LED: Press to display the message on the control panel.
Button on touch panel: Press to display the initial screen displayed at power-ON. Press 
[execution] on the touch panel and then the [CLEAR] button on the control panel. The screen 
then returns to the Button Check menu.

Authentication

screen

Normal

Warming up

Ready

[POWER]

OFF

To user

Each mode

Self-diagnosis 

mode

*1

*2

[POWER]

ON

[0][1]

[POWER]

LED lit/

LCD blinking

[START]

[START]

(Button check)

[POWER] OFF/ON

(Exit)

Summary of Contents for e-Studio477s



































































































































































































































































































































































































































































































Reviews:

No comments