manualshive.com logo in svg

Toshiba e-Studio477s, Service Manual, Page: 63 / 482

Share
Download
Toshiba e-Studio477s Service Manual Download Page 63

3

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO477S/527S/477SL

SELF-DIAGNOSTIC MODE

3 - 39

•  Version list

Fig. 3-30

The list of versions is output.

Notes: 

Some of the characters in the fonts that are used to print the version list are not supported. As a 
result, the language names under LANGUAGE VERSION may not be printed correctly when 
printing the version list.

VERSION LIST

 

 

 

 

 

   

20xx-xx-xx xx:xx

SYSTEM FIRMWARE ROM VERSION 

 

: Txxxxxxxxxxx

SYSTEM FIRMWARE INTERNAL ROM VERSION: Vx.x.x.xx.xx
PRINTER ROM VERSION 

 

: xxxM-xxx

SCANNER ROM VERSION 

 

: xxxS-xxx

PFC ROM VERSION 

 

 

: xxxF-xxx

RADF ROM VERSION   

 

: DF-xxx

FINISHER STACKER ROM VERSION 

 

: FIN-

FINISHER SADDLE ROM VERSION 

 

: SDL-

FINISHER PUNCH ROM VERSION 

 

: PUN-

CONVERTER ROM VERSION 

 

: CNV-xxx

FAX BOARD FIRMWARE ROM VERSION   

: Fxx-xxx

SYSTEM FIRMWARE OS VERSION 

 

: Vx.xxx.x.x

HDD DATA VERSION 

 

 

: Txxxxxxxxxxx

LANGUAGE VERSION
  English(US) 

 

 

 

: xxx.xxx  xxx xxx xx xx:xx:xx xxxx

CAPACITY OF HDD 

 

 

: xx.x GB

DEVICE INFORMATION OF HDD 

 

: xxx xxxxxxx-xxxxxx

SERIAL NUMBER OF HDD 

 

: xx-xxxxxxxxxxxx

MEMORY SIZE 

 

 

 

: xxxx MB / xxxx MB

INSTALLED ELK NAME   

 

: Data overwrite enabler

   

 

 

 

  IPSec enabler

   

 

 

 

  Meta scan enabler    

   

 

 

 

  External interface enabler                       

S/N: xxxxxxxxx

TOSHIBA e-STUDIOxxx

TOTAL: 9999999

DF TOTAL: 

9999999

Summary of Contents for e-Studio477s



































































































































































































































































































































































































































































































Reviews:

No comments