manualshive.com logo in svg

Toshiba e-Studio477s, Service Manual, Page: 456 / 482

Share
Download
Toshiba e-Studio477s Service Manual Download Page 456

 

Maintenance Utility Operating Manual 42678819FU02 - 20/38 

 

When the PU board setting value cannot be uploaded, the following error message is displayed. 

 

 

When the PU board setting value cannot be uploaded properly, the following error message is displayed. 

 

 

Click [OK] button in the error message window to display the following message. 

 

 

 

 

Click the [Finish] button on the "PU board replacement - Upload and Save" screen to disconnect the 

printer connected and return to "PU board replacement - Menu" screen. 

Could not upload or save the PU board setting value correctly. 

If you click [Finish], the upload process ends, and you will return to 

the "PU board replacement - Menu". 

Summary of Contents for e-Studio477s



































































































































































































































































































































































































































































































Reviews:

No comments