manualshive.com logo in svg

Toshiba e-Studio477s, Service Manual, Page: 166 / 482

Share
Download
Toshiba e-Studio477s Service Manual Download Page 166

e-STUDIO477S/527S/477SL

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

ERROR CODE AND TROUBLESHOOTING

5 - 62

[F109_4] Key consistency error (license data damage)

Take measures given in the following table according to the messages displayed in the SRAM Licence 
Status and FROM Licence Status fields. 

Remarks: 

If the error is not cleared, reinstallation of the system firmware, system software and application 
is needed. ([4]+[9] 



Power-ON)

* AccessFailed or KeyMismatch

Classification

Contents

Other service call

Key consistency error - The license data are damaged.

Check item

Measures

Encryption key status confirmation

Check the message displayed by [3] + [C] + [POWER] 

 5. Key 

Backup Restore.

SRAM Licence 

Status

FROM Licence 

Status

Measure

*

AccessFailed

Replace the SYS board.

 P. 6-18 "6.2.4 Precautions and Procedures when replacing 

the SYS board" (all steps)
<With USB backup data: All key data recovery>
1. Recover all the data on the SRAM board.

[5] + [9] + [POWER] 

 2. Restore SRAM Data from USB

(For details, see "9.1.4Cloning procedure [B]Restore 
procedure")

2. Recover the encryption key/license on the SYS board.

Follow the procedures below noted in "6.2.4Precautions 
and Procedures when replacing the SYS board".
[C] Restore ADI key (only when ADI-HDD is installed)
[D] Restore encryption key
[E] Restore license

AccessFailed

*

Replace the SYS board.

 P. 6-22 "6.2.5 Precautions and procedure when replacing 

the SRAM board (for the SYS board)" (all steps)

KeyMismatch

KeyMismatch

<The error occurs when the SYS board is replaced>
Recover the license on the SYS board. (Transfer the license 
from SYS-SRAM to SYS-FROM.)

 P. 6-18 "6.2.4 Precautions and Procedures when replacing 

the SYS board"([E]Restore license)
<The error occurs except when the SYS board is replaced>
Recover the license on the SRAM board. (Transfer the license 
from SYS-FROM to SYS-SRAM.)

 P. 6-22 "6.2.5 Precautions and procedure when replacing 

the SRAM board (for the SYS board)"([I]Backup license)

Summary of Contents for e-Studio477s



































































































































































































































































































































































































































































































Reviews:

No comments