manualshive.com logo in svg

Toshiba e-Studio477s, Service Manual, Page: 291 / 482

Share
Download
Toshiba e-Studio477s Service Manual Download Page 291

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO477S/527S/477SL

FIRMWARE UPDATING

8 - 3

8

Notes: 

• Written firmware varies depending on the kinds of the boards provided as service parts. For 

updating, only the minimum firmware is installed on the system control PC board, logic PC board, 
scanning section control PC board, and FAX board. The latest version of the firmware at the time 
of delivery is written on the RADF control PC board and finisher control PC board.
When any of above boards is replaced with a new one in the field, check the other firmware 
version used and then update with a corresponding suitable version.

• "Can't fetch Ver." is displayed in the Installed Version field when the version of the installed 

firmware cannot be acquired properly. If a normal power on is not performed after the firmware is 
updated and the [ON/OFF] button is pressed while simultaneously holding down the [4] and [9] 
buttons, "Can't fetch Ver." may be displayed on the control panel for some firmwares. A normal 
power on must be performed.

Summary of Contents for e-Studio477s



































































































































































































































































































































































































































































































Reviews:

No comments