manualshive.com logo in svg

Toshiba e-Studio477s, Service Manual, Page: 215 / 482

Share
Download
Toshiba e-Studio477s Service Manual Download Page 215

6

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO477S/527S/477SL

REPLACEMENT OF PC BOARDS/HDD

6 - 1

6. REPLACEMENT OF PC BOARDS/HDD

6.1

Removal and Installation of PC Boards/HDD

Refer to the Hardware Guide for the removal and installation procedures of the PC boards other than 
the SYS board, HDD, and SRAM board <for SYS board>.

Notes: 

When the PC board/HDD is replaced, refer to the respective Notes and Cautions of 
“Replacement of PC boards and HDD” in 

 P. 6-9 "6.2 Precautions, Procedures and Settings 

for Replacing PC Boards and HDD".

6.1.1

Right side cover

(1) Remove two screws.

Fig.6-3

(2) Remove the screw located at the bottom of 

the right side cover.

Fig.6-4

Summary of Contents for e-Studio477s



































































































































































































































































































































































































































































































Reviews:

No comments