manualshive.com logo in svg

Toshiba e-Studio477s, Service Manual, Page: 244 / 482

Share
Download
Toshiba e-Studio477s Service Manual Download Page 244

e-STUDIO477S/527S/477SL

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

REPLACEMENT OF PC BOARDS/HDD

6 - 30

6.2.9

License re-registration using the one-time dongle

[ 1 ] Re-registration when the board is replaced

The license registered using the one-time dongle can be re-registered only in the same equipment. 
When the SYS board or SRAM board (for SYS board) is replaced, follow the procedures for re-
registration given below.

(1) Start up with the Setting Mode (08).

(2) Enter the password, and then press the [OK] button.

 (If the password is not set for Service, press the [ENTER] button without entering anything.)

(3) Key in [3840], and then press the [START] button.

(4) Press the [INSTALL] button.

(5) Install the one-time dongle in the equipment (the one which you used for registering the selected 

license), and then press the [OK] button.

(6) Select the license to be installed, and then press the [INSTALL] button.

(7) The screen for notifying that the installation will be started is displayed. Then press the [YES] 

button.

(8) After 10 to 40 seconds have passed, the screen for notifying the success of the performance is 

displayed. Then press the [OK] button. If the screen for notifying a failure of the performance is 
displayed, quit this operation by pressing the [CLOSE] button. Then check that the one-time 
dongle, which you used for uploading the selected license, is installed in the equipment.

(9) Check that the installed license is displayed on the license list.

Remarks: 

If there are any other licenses to be returned, repeat from step (4). If there are no other licenses 
to be returned, press the [CLOSE] button, and then turn the power OFF.

Notes: 

This procedure is available only with the one-time dongle used for the previous registration, since 
the model information registered in it is utilized. Use the same one-time dongle and the 
equipment when registering the license.

[ 2 ] Re-registration when the equipment is replaced due to malfunction

When the equipment has to be replaced due to a malfunction, return the license registered in the 
equipment to the one-time dongle and register it to the new equipment following the procedure below.

Notes: 

The license of the IPSec Enabler (GP-1080) cannot be reinstalled. The one-time dongle to be 
used is the one for the previous registration of the license. The license is deleted from the 
equipment and is stored in the one-time dongle.
Do not perform the deletion of PDFA Converter since it is deleted without any return to the one-
time dongle.

(1) Start up with the Setting Mode (08).

(2) Enter the password, and then press the [OK] button.

(If the password is not set for Service, press the [ENTER] button without entering anything.)

(3) Key in [3840], and then press the [START] button.

(4) Select the license to be returned, and then press the [REMOVE] button.

Summary of Contents for e-Studio477s



































































































































































































































































































































































































































































































Reviews:

No comments