Toshiba e-Studio477s Service Manual Download Page 346

Page: 346 / 482

e-STUDIO477S/527S

05/08

Mode

Element

Sub Element

Item

Subitem

Code

Sub-

Code

Details

Default

value

Acceptable

value

RAM

Contents

Proc

edure

ServiceUI

PCL

The smaller the value, the more fain text is

suppressed. The larger the value, the more

smudged text is suppressed.

Adjustment

mode

Image

Processing

Smoothing

processing

PRT(black)

7326

0~2

SYS

XPS

The smaller the value, the more fain text is

suppressed. The larger the value, the more

smudged text is suppressed.

Adjustment

mode

Image

Processing

Smoothing

processing

PRT(black)

7327

0~2

SYS

Low density

When the value increases, the density in the target

area becomes higher.

Adjustment

mode

Image

Processing

Gamma

balance

adjustment

Monochrome/600

dpi/Auto

PS/Text

7360

128

0~255

Yes

SYS

Medium density

When the value increases, the density in the target

area becomes higher.

Adjustment

mode

Image

Processing

Gamma

balance

adjustment

Monochrome/600

dpi/Auto

PS/Text

7360

128

0~255

Yes

SYS

High density

When the value increases, the density in the target

area becomes higher.

Adjustment

mode

Image

Processing

Gamma

balance

adjustment

Monochrome/600

dpi/Auto

PS/Text

7360

128

0~255

Yes

SYS

Low density

When the value increases, the density in the target

area becomes higher.

Adjustment

mode

Image

Processing

Gamma

balance

adjustment

Monochrome/600

dpi/Auto

PS/Graphics

7361

128

0~255

Yes

SYS

Medium density

When the value increases, the density in the target

area becomes higher.

Adjustment

mode

Image

Processing

Gamma

balance

adjustment

Monochrome/600

dpi/Auto

PS/Graphics

7361

128

0~255

Yes

SYS

High density

When the value increases, the density in the target

area becomes higher.

Adjustment

mode

Image

Processing

Gamma

balance

adjustment

Monochrome/600

dpi/Auto

PS/Graphics

7361

128

0~255

Yes

SYS

Low density

When the value increases, the density in the target

area becomes higher.

Adjustment

mode

Image

Processing

Gamma

balance

adjustment

Monochrome/600

dpi/Auto

PS/Image

7362

128

0~255

Yes

SYS

Medium density

When the value increases, the density in the target

area becomes higher.

Adjustment

mode

Image

Processing

Gamma

balance

adjustment

Monochrome/600

dpi/Auto

PS/Image

7362

128

0~255

Yes

SYS

High density

When the value increases, the density in the target

area becomes higher.

Adjustment

mode

Image

Processing

Gamma

balance

adjustment

Monochrome/600

dpi/Auto

PS/Image

7362

128

0~255

Yes

SYS

Low density

When the value increases, the density in the target

area becomes higher.

Adjustment

mode

Image

Processing

Gamma

balance

adjustment

Monochrome/600

dpi/Auto

XPS/Text

7366

128

0~255

Yes

SYS

Medium density

When the value increases, the density in the target

area becomes higher.

Adjustment

mode

Image

Processing

Gamma

balance

adjustment

Monochrome/600

dpi/Auto

XPS/Text

7366

128

0~255

Yes

SYS

High density

When the value increases, the density in the target

area becomes higher.

Adjustment

mode

Image

Processing

Gamma

balance

adjustment

Monochrome/600

dpi/Auto

XPS/Text

7366

128

0~255

Yes

SYS

Low density

When the value increases, the density in the target

area becomes higher.

Adjustment

mode

Image

Processing

Gamma

balance

adjustment

Monochrome/600

dpi/Auto

XPS/Graphics

7367

128

0~255

Yes

SYS

Medium density

When the value increases, the density in the target

area becomes higher.

Adjustment

mode

Image

Processing

Gamma

balance

adjustment

Monochrome/600

dpi/Auto

XPS/Graphics

7367

128

0~255

Yes

SYS

High density

When the value increases, the density in the target

area becomes higher.

Adjustment

mode

Image

Processing

Gamma

balance

adjustment

Monochrome/600

dpi/Auto

XPS/Graphics

7367

128

0~255

Yes

SYS

Ver03

05 Adjustment Mode

Summary of Contents for e-Studio477s


























































































































































































































































































































































































































































































Search results

Summary of Contents for e-Studio477s

Reviews:

Toshiba e-Studio477s, Service Manual, Page: 346 / 482

Search results

Summary of Contents for e-Studio477s

Reviews: