Toshiba e-Studio477s Service Manual Download Page 360

Page: 360 / 482

e-STUDIO477S/527S

05/08

Mode

Element

Sub Element

Item

Subitem

Code

Sub-

Code

Details

Default

value

Acceptable

value

RAM

Contents

Proc

edure

ServiceUI

Switching printer setting

DPWS printer function is switched.

1: Enabled

2: Disabled

Setting

mode

System

Network

DPWS

3754

1~2

NIC

Switching scanner setting

DPWS scanner function is switched.

1: Enabled

2: Disabled

Setting

mode

System

Network

DPWS

3755

1~2

NIC

Discovery Port Number

Port number used for DPWS Discovery

Setting

mode

System

Network

DPWS

3757

3702

1~65535

NIC

Metadata Exchange Port

Number

Port number used for DPWS Metadata Exchange

Setting

mode

System

Network

DPWS

3758

50081

1~65535

NIC

Print Port Number

Port number used for DPWS Print

Setting

mode

System

Network

DPWS

3759

50082

1~65535

NIC

Scan Port Number

Port number used for DPWS Scan

Setting

mode

System

Network

DPWS

3760

50083

1~65535

NIC

Print Max numbers of

connection

Maximum numbers received from more than one

connection request in the DPWS print

Setting

mode

System

Network

DPWS

3765

1~20

NIC

Print Max numbers of

reception

Maximum numbers of data received from more

than one clients in the DPWS print

Setting

mode

System

Network

DPWS

3766

1~20

NIC

Switching IPv6 setting

IPv6 function is switched.

1: Enabled

2: Disabled

Setting

mode

System

Network

IPv6

3767

1~2

NIC

Switching address

acquisition

IP (IPv6) address acquisition setting is switched.

1: Manual

2: Stateless

3: Stateful

Setting

mode

System

Network

IPv6

3768

1~3

NIC

IPv6 Address

Displays IPv6 address. Maximum 40 characters

(byte).

Setting

mode

System

Network

IPv6

3770

Prefix display setting

Sets the length of the displayed prefix. Maximum 3

characters (byte).

Setting

mode

System

Network

IPv6

3771

Default Gateway setting

Sets the default gateway for IPv6 address.

Maximum 40 characters (byte).

Setting

mode

System

Network

IPv6

3772

DHCPv6 Option setting

DHCPv6 Option is switched when the Manual is

set.

1: Enabled

2: Disabled

Setting

mode

System

Network

3774

1~2

NIC

Stateless Address setting

IP Address is acquired by both Stateless and State

full Address.

1: Enabled

2: Disabled

Setting

mode

System

Network

3777

1~2

NIC

Acquiring DHCPv6 Option

When Stateless Address is selected, an option is

acquired from DHCPv6 server.

1: Enabled

2: Disabled

Setting

mode

System

Network

3778

1~2

NIC

State full Address setting

IP Address is acquired from DHCPv6 server.

1: Enabled

2: Disabled

Setting

mode

System

Network

3779

1~2

NIC

State full Option setting

An option is acquired from DHCPv6 server.

1: Enabled

2: Disabled

Setting

mode

System

Network

3780

1~2

NIC

Ver03

08 Setting Mode

Summary of Contents for e-Studio477s


























































































































































































































































































































































































































































































Search results

Summary of Contents for e-Studio477s

Reviews:

Toshiba e-Studio477s, Service Manual, Page: 360 / 482

Search results

Summary of Contents for e-Studio477s

Reviews: