Toshiba e-studio 2555c Troubleshooting Manual Download Page 61

Page: 61 / 136

1 TROUBLESHOOTING FOR THE HARDWARE

Replacing the Waste Toner Box 59

Replacing the Waste Toner Box

When the waste toner box becomes full, the symbol for replacement of the waste toner box blinks and the
message “Dispose of used toner” appears. Replace the waste toner box following the procedure below.

Never attempt to incinerate waste toner boxes.

Dispose of used toner cartridges and waste toner boxes in accordance with local regulations.

Open the front cover of the equipment.

Put your fingers in the waste toner box front grooves
and take it out toward you pushing down the top
latch.

Never attempt to incinerate waste toner boxes.

Dispose of used toner cartridges and waste toner boxes in
accordance with local regulations.

Place the waste toner box on a large sheet so as not
to dirty the floor.

Do not place the waste toner box with its collecting port
face down.

The waste toner may spill out from the box's collecting port.

Take the new waste toner box out of the carton.

Summary of Contents for e-studio 2555c








































































































































Search results

Summary of Contents for e-studio 2555c

Reviews:

Related manuals for e-studio 2555c

Brands by name

Popular brands

Toshiba e-studio 2555c, Troubleshooting Manual

Search results

Summary of Contents for e-studio 2555c

Reviews:

Related manuals for e-studio 2555c

Brands by name

Popular brands