manualshive.com logo in svg

Toshiba e-studio 2555c, Troubleshooting Manual

The Toshiba e-studio 2555c Troubleshooting Manual is an essential resource for resolving any technical issues that may arise with this high-performance multifunction printer. This comprehensive manual can be downloaded for free from manualshive.com, providing users with step-by-step instructions and solutions to keep their devices running smoothly.

Share
Download
background image

1.

TROUBLESHOOTING FOR THE HARDWARE

This chapter describes how to troubleshoot problems with paper, toner and other finishing processes.
This chapter also describes how to supply the paper, toner and staples.

When This Screen Is Displayed .............................................................................................. 8

Messages Displayed on the Touch Panel ............................................................................ 10

Clearing a Paper Misfeed....................................................................................................... 15

Locating a paper misfeed .....................................................................................................................................15
Clearing a paper misfeed .....................................................................................................................................16
Paper misfeed in the Reversing Automatic Document Feeder (Lower) ...............................................................17
Paper misfeed in the Reversing Automatic Document Feeder (Upper) ...............................................................18
Paper misfeed in the drawer feeding portion........................................................................................................19
Paper misfeed in the Large Capacity Feeder .......................................................................................................20
Paper misfeed in the Paper Feed Pedestal..........................................................................................................20
Paper misfeed in the drawer ................................................................................................................................21
Paper misfeed in the drawer of the Large Capacity Feeder .................................................................................21
Paper misfeed in the bypass tray .........................................................................................................................22
Paper misfeed in the automatic duplexing unit.....................................................................................................23
Paper misfeed on the paper transport path ..........................................................................................................24
Paper misfeed in the fuser unit.............................................................................................................................24
Paper misfeed in the Bridge Kit............................................................................................................................26
Paper misfeed in the Finisher and the Hole Punch Unit.......................................................................................26
Paper misfeed in the Saddle Stitch Finisher and the Hole Punch Unit.................................................................30
Paper misfeed in the Saddle Stitch unit of the Saddle Stitch Finisher..................................................................33
Paper misfeed in the Inner Finisher and the Hole Punch Unit .............................................................................38
Clearing paper misfeeds caused by a wrong paper size setting ..........................................................................41

Clearing a Staple Jam ............................................................................................................ 46

Staple jam in the finisher ......................................................................................................................................46
Staple jam in the Saddle Stitch unit ......................................................................................................................50

Replacing a Toner Cartridge ................................................................................................. 52

Replacing a “Near Empty” toner cartridge............................................................................................................55

Replacing the Waste Toner Box............................................................................................ 59

Refilling With Staples............................................................................................................. 61

Refilling finisher staples........................................................................................................................................61
Refilling Saddle Stitch unit staples........................................................................................................................64

Cleaning the Main Chargers and LED Print Heads ............................................................. 67

Cleaning the Hole Punch Dust Bin ....................................................................................... 70

Finisher / Saddle Stitch Finisher Hole Punch Unit................................................................................................70
Inner Finisher Hole Punch Unit ............................................................................................................................70

When Printed Sheets Overflow from the Exit Tray.............................................................. 72

Summary of Contents for e-studio 2555c









































































































































Reviews:

No comments

Related manuals for e-studio 2555c

Xerox All in One Printer Product Safety Data Sheet preview
All in One Printer
Brand: Xerox Pages: 3
DataCard CR500 Quick Install Manual preview
CR500
Brand: DataCard Pages: 17
DataCard CR500 User Reference Manual preview
CR500
Brand: DataCard Pages: 24
Magicard Rio Pro Getting Started Manual preview
Rio Pro
Brand: Magicard Pages: 30
Magicard Rio Pro User Manual preview
Rio Pro
Brand: Magicard Pages: 35
Magicard MAGICARD ID Card Printer Driver Manual preview
MAGICARD ID Card Printer
Brand: Magicard Pages: 30
Magicard Rio 2e Brochure preview
Rio 2e
Brand: Magicard Pages: 6
Xerox DocuColor 1632 Printing User Manual preview
DocuColor 1632
Brand: Xerox Pages: 130
Xerox Phaser 6500 Service Manual preview
Phaser 6500
Brand: Xerox Pages: 793
Ricoh AP-P2 G188 Field Service Manual preview
AP-P2 G188
Brand: Ricoh Pages: 682
Duplo DP - M400 Instruction Manual preview
DP - M400
Brand: Duplo Pages: 123
DataCard SD260L Installation And Administrator'S Manual preview
SD260L
Brand: DataCard Pages: 130
Konica Minolta Bizhub 4020 Shortcut Manual preview
Bizhub 4020
Brand: Konica Minolta Pages: 40
Ricoh SG 7100DN Installation Manual preview
SG 7100DN
Brand: Ricoh Pages: 17
Oki ES9455 Printing Manual preview
ES9455
Brand: Oki Pages: 204
Oki LP-2050-MF User Manual preview
LP-2050-MF
Brand: Oki Pages: 246
EBS EBS-6500 Basic Manual preview
EBS-6500
Brand: EBS Pages: 20
IDVille ID MAKER Zenius User Manual preview
ID MAKER Zenius
Brand: IDVille Pages: 66

Brands by name

Popular brands

Load more brands