Toshiba e-studio 2555c Troubleshooting Manual Download Page 49

Page: 49 / 136

1.TROUBLESHOOTING FOR THE HARDWARE

Clearing a Staple Jam 47

1 TROUBLESHOOTING FOR THE HARDWARE

Close the front cover of the finisher.

Inner Finisher

Holding the knob, raise the guide, and return it to its
original position.

Remove the staples fallen between the staple
cartridge and the staple case or the ones in the staple
receiver.

Fit the staple cartridge into the stapler.

When fitting the staple cartridge, hold the green-labeled portion
of the bracket securely so that the bracket will not move.
Insert the cartridge until it is caught by the latch and fixed with a
click.

Lift up the control panel and then open the front cover
of the finisher.

Summary of Contents for e-studio 2555c








































































































































Search results

Summary of Contents for e-studio 2555c

Reviews:

Related manuals for e-studio 2555c

Brands by name

Popular brands

Toshiba e-studio 2555c, Troubleshooting Manual

Search results

Summary of Contents for e-studio 2555c

Reviews:

Related manuals for e-studio 2555c

Brands by name

Popular brands