Toshiba e-studio 2555c Troubleshooting Manual Download

Page: 10 / 136

1 TROUBLESHOOTING FOR THE HARDWARE

8 When This Screen Is Displayed

When This Screen Is Displayed

Various screens are displayed on the touch panel depending on the state of the equipment. This section
describes how to solve problems with some of the screen examples.

Screen

Description / Remedy

A message appears on the upper
part of the screen to notify users
of a problem, etc. For the major
examples, see the following
pages.

P.10 “Messages Displayed on

the Touch Panel”

The original or copy paper is
misfed. Remove it following the
guidance on the touch panel.

P.15 “Clearing a Paper

Misfeed”

A cover is open. Check which
cover on the touch panel and
then close it securely.

Summary of Contents for e-studio 2555c








































































































































Search results

Summary of Contents for e-studio 2555c

Reviews:

Related manuals for e-studio 2555c

Brands by name

Popular brands

Toshiba e-studio 2555c, Troubleshooting Manual

Search results

Summary of Contents for e-studio 2555c

Reviews:

Related manuals for e-studio 2555c

Brands by name

Popular brands