Toshiba e-studio 2555c Troubleshooting Manual Download | Manualshive

Page: 100 / 136

background image

6 TROUBLESHOOTING FOR NETWORK CONNECTIONS

98 Locating the Equipment in the Network

Equipment does not respond to ping command

Problem Description

The equipment does not respond to a ping command.

Corrective Action

Check the network settings following the checklist below.

No

.

Check...

Yes

No

Corrective Action

1

Confirm that the TCP/IP protocol suite
is installed on the client computer.

Next

Step

Ø

Ö

Refer to the networking section of your
operating system documentation.

2

Look at the NIC configuration page and
confirm that the TCP/IP settings are
correct. Is the IP address entered and
valid? Are the Gateway and Subnet
settings correct?

Next

Step

Ø

Ö

Enter the correct TCP/IP settings.

3

Reboot the equipment. Check the NIC
Configuration page that is printed out.
Are the TCP/IP settings correct?

Next

Step

Ø

Ö

The settings are not binding, contact
your service representative.

4

Try to ping the equipment again. Did the
equipment respond to the ping?

End

Next

Step

Ø

5

Can you ping the equipment from any
other computer within the same
network? If not, the equipment might
have an IP address that is out of range
or invalid.

Next

Step

Ø

Ö

Contact your local network specialist for
a valid IP address for the equipment.

6

Can you ping to another computer
within the same network?

Next

Step

Ø

Ö

Check the computer’s protocol settings
to make sure the gateway and subnet
settings are correct.

7

If you have customized the device
name, you can check if the NIC is
functional by restoring the default
settings. When the equipment
automatically reboots and an NIC
Configuration page is printed, does the
device name include the NIC’s unit
serial number?

Next

Step

Ø

Ö

The NIC is faulty or improperly installed.
Contact your service representative.

8

Check link activities on the port being
used by the equipment and also the
integrity of the network cable, hub, or
switch that is connecting the equipment
to the network. Replace any network
components that you suspect are faulty.
Can you ping the equipment now?

End

Ö

Contact your service representative.

«
...
98
99
100
101
102
...
»

Summary of Contents for e-studio 2555c









































































































































Reviews:

No comments

Related manuals for e-studio 2555c

Brand: Oki Pages: 6

Brand: Oki Pages: 44

Brand: Oki Pages: 13

Brand: Oki Pages: 20

Brand: Oki Pages: 2

Brand: Oki Pages: 28

Brand: YOUPAI Pages: 15

Brand: TallyGenicom Pages: 15

Brand: Xerox Pages: 414

Brand: Xante Pages: 6

Brand: Xerox Pages: 15

Brand: Xerox Pages: 9

DocuPrint 180 NPS Series

Brand: Xerox Pages: 172

Brand: Xerox Pages: 11

Brand: Xerox Pages: 8

Brand: Xerox Pages: 40

Brand: Xerox Pages: 28

Color C75 Press

Brand: Xerox Pages: 340

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands