Toshiba e-studio 2555c Troubleshooting Manual Download

Page: 57 / 136

1.TROUBLESHOOTING FOR THE HARDWARE

Replacing a Toner Cartridge 55

1 TROUBLESHOOTING FOR THE HARDWARE

Replacing a “Near Empty” toner cartridge

The message “Toner near Empty” appears on the touch panel when there is not much toner left in a toner
cartridge.

Some toner is still left in the toner cartridge while the message “Toner near Empty” is displayed. You do not
have to replace the toner cartridge yet, but if you choose to do so, follow the procedure below.

Pull out the cleaner until the mark appears and return
it. Repeat this 3 times for each of the 4 colors.

The cleaner cannot be removed by design. Pulling it out
forcibly may cause malfunction.

Close the front cover pressing both edges.

2 3

Summary of Contents for e-studio 2555c








































































































































Search results

Summary of Contents for e-studio 2555c

Reviews:

Related manuals for e-studio 2555c

Brands by name

Popular brands

Toshiba e-studio 2555c, Troubleshooting Manual

Search results

Summary of Contents for e-studio 2555c

Reviews:

Related manuals for e-studio 2555c

Brands by name

Popular brands