Toshiba e-studio 2555c Troubleshooting Manual Download Page 63

Page: 63 / 136

1 TROUBLESHOOTING FOR THE HARDWARE

Refilling With Staples 61

Refilling With Staples

Refill with staples according to the following procedures when the staples in the stapler of the finisher and
saddle stitch unit run out.

P.61 “Refilling finisher staples”

P.64 “Refilling Saddle Stitch unit staples”

Refilling finisher staples

Finisher / Saddle Stitch Finisher

Open the front cover of the finisher.

Remove the staple cartridge.

Take the empty staple case out of the staple cartridge.

Pull up the empty staple case while pushing both sides as
shown in the figure.

Fit a new staple case on the staple cartridge.

Push the staple case hook into the staple cartridge socket until
you hear a click.

Summary of Contents for e-studio 2555c








































































































































Search results

Summary of Contents for e-studio 2555c

Reviews:

Related manuals for e-studio 2555c

Brands by name

Popular brands

Toshiba e-studio 2555c, Troubleshooting Manual

Search results

Summary of Contents for e-studio 2555c

Reviews:

Related manuals for e-studio 2555c

Brands by name

Popular brands