Toshiba e-studio 2555c Troubleshooting Manual Download Page 19

Page: 19 / 136

1.TROUBLESHOOTING FOR THE HARDWARE

Clearing a Paper Misfeed 17

1 TROUBLESHOOTING FOR THE HARDWARE

If paper misfeeds occur frequently

The following are the common causes of paper misfeeds. If the problem persists, check for the following
situations.

An unsuitable original is placed on the Reversing Automatic Document Feeder.

Unavailable paper with the equipment is used.

Paper sizes are not consistent between the size in a drawer or the bypass tray and the size registered in
the equipment.

All the misfed paper has not been removed.

There is too much of a gap between the paper and the side or end guide in the drawer.

The amount of paper placed in a drawer exceeds the limit indicated on the side guide of the drawer.

Paper misfeed in the Reversing Automatic Document Feeder (Lower)

Open the Reversing Automatic Document Feeder.

Lower the green lever, open the reverse cover and
remove the original.

Close the Reversing Automatic Document Feeder.

Summary of Contents for e-studio 2555c








































































































































Search results

Summary of Contents for e-studio 2555c

Reviews:

Related manuals for e-studio 2555c

Brands by name

Popular brands

Toshiba e-studio 2555c, Troubleshooting Manual

Search results

Summary of Contents for e-studio 2555c

Reviews:

Related manuals for e-studio 2555c

Brands by name

Popular brands