Toshiba e-studio 2555c Troubleshooting Manual Download Page 34

Page: 34 / 136

1 TROUBLESHOOTING FOR THE HARDWARE

32 Clearing a Paper Misfeed

If the paper size is small, turn the knob shown in the following figures to send the
paper, and then remove the misfed paper.

When the Hole Punch Unit is installed, open the front cover of the finisher and turn the 2 knobs at
the same time.

Close the cover of the Bridge Unit.

Lower the shutter of the paper exit portion and
remove the paper.

Close the upper receiving tray of the finisher.

Place your hands on the near and far side of the lever and push
to close the tray until it clicks.

Be careful not to let your fingers be caught between the
finisher body and the upper tray of the finisher

This could injure you.

The upper receiving tray of the finisher can also be closed by
pressing the right side of the lever.

When the Hole Punch Unit is not installed

When the Hole Punch Unit is installed

Summary of Contents for e-studio 2555c








































































































































Search results

Summary of Contents for e-studio 2555c

Reviews:

Related manuals for e-studio 2555c

Brands by name

Popular brands

Toshiba e-studio 2555c, Troubleshooting Manual

Search results

Summary of Contents for e-studio 2555c

Reviews:

Related manuals for e-studio 2555c

Brands by name

Popular brands