Toshiba e-studio 2555c Troubleshooting Manual Download Page 16

Page: 16 / 136

1 TROUBLESHOOTING FOR THE HARDWARE

14 Messages Displayed on the Touch Panel

Error Codes

The error codes indicating the status of the equipment may appear on the touch panel. You can find the
listings of these error codes in Chapter 7.

P.112 “Error Codes”

USER Quota exceeded.
Contact the Administrator.

The copying, printing or
scanning quota to the user
has reached “0”.

For details of setting the quota, ask your
administrator.

USER and DEPARTMENT
Quota exceeded.
Contact the Administrator.

The copying, printing or
scanning quota to the user
and department has reached
“0”.

For details of setting the quota, ask your
administrator.

Check under the Finisher tray
and reboot the machine.

An obstruction is placed under
the Finisher tray.

Remove the obstruction under the Finisher
tray and reboot the equipment.

The number of originals
exceeds the limits.
The scanned data are
deleted.

The number of originals to be
scanned has exceeded the
limit of 1000 sheets during
scanning. (The magazine sort
or page number function is
used.)

Reduce the number of originals to be
scanned, and try again.

The number of originals
exceeds the limits.
Will you copy stored
originals?

The number of originals to be
scanned has exceeded the
limit of 1000 sheets during
scanning.

To print out the data for the originals stored
(scanned) until the message appeared,
press [YES] on the touch panel. To delete
the stored data, press [NO].

LAN cable is not detected

The LAN cable connection is
not detected.

Check the following items.

Check that the LAN cable is connected
to the equipment.

Check that there is no damage on the
connector of the LAN cable.

Check that the LAN cable is open
circuited.

Check that the LAN cable is connected
to the HUB. Check that there is no
damage to the connector.

Check that the power is ON for the HUB
to which the LAN cable is connected.

Check that the settings of the
communication speed and the Ethernet
method for the equipment and the HUB
are aligned.

Message

Problem Description

Corrective Action

Summary of Contents for e-studio 2555c








































































































































Search results

Summary of Contents for e-studio 2555c

Reviews:

Related manuals for e-studio 2555c

Brands by name

Popular brands

Toshiba e-studio 2555c, Troubleshooting Manual

Search results

Summary of Contents for e-studio 2555c

Reviews:

Related manuals for e-studio 2555c

Brands by name

Popular brands