Terasic MAX10-Plus User Manual Download Page 10 | Manualshive

Page: 10 / 87

background image

MAX 10 Plus User
Manual

10

www.terasic.com

May 31, 2019

Chapter 3

Using the MAX 10 Plus

This chapter provides an instruction to use the board and describes the peripherals.

3.1

Configuration of MAX 10 FPGA on MAX 10 Plus

There are two types of configuration method supported by MAX 10 Plus:

1. JTAG configuration: configuration using JTAG port.

JTAG configuration scheme allows you to directly configure the device core through JTAG pins -
TDI, TDO, TMS, and TCK pins. The Quartus II software automatically generates .sof that is used
for JTAG configuration with a download cable in the Quartus II software programmer.

2. Internal configuration: configuration using internal flash.

Before  internal  configuration,  you  need  to  program  the  configuration  data  into  the  configuration
flash  memory  (CFM)  which  provides  non-volatile  storage  for  the  bit  stream.  The  information  is
retained  within  CFM  even  if  the  MAX  10  Plus  is  turned  off.  When  the  board  is  powered  on,  the
configuration data in the CFM is automatically loaded into the MAX 10 FPGA.

◼

JTAG Chain on MAX 10 Plus

The FPGA device can be configured through JTAG interface on MAX 10 Plus board, but the JTAG
chain must form a closed loop, which allows Quartus II programmer to the detect FPGA device.

illustrates the JTAG chain on MAX 10 Plus.

Figure 3-1 Path of the JTAG Chain

◼

Configure the FPGA in JTAG Mode

The following shows how the FPGA is programmed in JTAG mode step by step.

1.

Open the Quartus II programmer and click

Auto Detect

, as circled in

Figure 3-2.

«
...
8
9
10
11
12
...
»

Summary of Contents for MAX10-Plus
























































































Reviews:

No comments

Related manuals for MAX10-Plus

Brand: Lantronix Pages: 17

Brand: Intel Pages: 89

Brand: TYAN Pages: 82

Brand: NXP Semiconductors Pages: 32

IMBA-BDE-1518-R10

Brand: IEI Technology Pages: 14

Brand: Sundance Spas Pages: 21

126791-HMC764LP6C

Brand: Analog Devices Pages: 18

Brand: Aaeon Pages: 111

Brand: Memec Pages: 45

Brand: IWILL Pages: 54

Brand: MSI Pages: 73

Brand: Engbo Pages: 64

Brand: Gigabyte Pages: 46

Brand: ASROCK Pages: 98

Brand: Gigabyte Pages: 20

Brand: Pentium Pages: 48

EVB-LAN9252-SPI

Brand: Microchip Technology Pages: 22

Brand: Biostar Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands