Tennant 5400 Service Manual Download Page 52

Page: 52 / 163

SCRUBBING

3-28

5400 330735 (3–01)

8. Install a new seal (part # 222820). Apply a

bead of silicone sealant (part # 08317)
around the seal to bond it in place. Reinstall
the lower cover and gasket.

9. Using the M8 hex screw located under the

brush motor, tension the belt by applying
2.5–2.7 lbs of force per belt at the middle of
the span that is opposite the belt travel with
a deflection of 0.10 inch.

10. Tighten the two pivot bolts to 18 – 24 Nm

(15 – 20 ft lb). Re–check the belt tension.

11. Reinstall the belt cover. Install the two M6

hex screws, and washers. Tighten to 11 – 14
Nm (7 – 10 ft lb).

12. Reinstall the scrub brush. See TO

REPLACE A CYLINDRICAL SCRUB
BRUSH instructions in this section.

13. Operate the machine and check for proper

operation.

Summary of Contents for 5400




































































































































































Search results

Summary of Contents for 5400

Reviews:

Related manuals for 5400

Brands by name

Popular brands

Tennant 5400, Service Manual

Search results

Summary of Contents for 5400

Reviews:

Related manuals for 5400

Brands by name

Popular brands