Tennant 5400 Service Manual Download Page 28 | Manualshive

Page: 28 / 163

background image

SCRUBBING

3-4

5400 330735 (3–01)

SOLUTION TANK

The solution tank holds the clean water and
detergent mixture that will be applied to the floor
for the scrubbing operation. The solution tank is
also the main frame component.

The solution tank does not require regular
maintenance except daily rinsing of any sludge or
deposits. If any deposits do form on the bottom of
the tank, rinse with a strong blast of warm water.

NOTE: The water must not be hotter than 60

C

(140

F), or tank damage may occur. Do not use

steam to clean the tank.

ES

Option: The recovery tank should be

partially filled with clean water after using the
ES

Option and clean water should be run

through the pump until it is clear of any deposits.

«
...
26
27
28
29
30
...
»

Summary of Contents for 5400




































































































































































Reviews:

No comments

Related manuals for 5400

Brand: Daedalus Pages: 20

Brand: C.P.Bourg Pages: 142

Brand: Kärcher Pages: 55

Brand: Baby Lock Pages: 56

Brand: Adler Pages: 5

ADVANTAGE-400H Series

Brand: U.S. Products Pages: 8

Brand: Pfaff Pages: 150

Brand: Janome Pages: 52

Brand: Singer Pages: 18

Brand: Geemarc Pages: 84

Brand: Shark Pages: 41

imagePRESS C7010VPS/C6010VPS/C6010S Series

Brand: Canon Pages: 100

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands